Encore 24 PORTS NWAY SWITCHING HUB User's Guide Page 123
- Page / 198
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
6-1
6
Diagnostics and
Troubleshooting
6
To verify your connections and T1 line, run diagnostics from Menu-9 Diagnostics:
¥ Self test
¥ Loop DTE test
¥ Loop NET test
¥ Loop Payload test
¥ Loop Up Remote test
¥ Various Pattern tests
¥ Loop Down Remote test
¥ NET/DTE LPBK Test
¥ Lamp test
¥ DTE/NET Loopback Test
You can also run these tests from the front panel. Refer to Chapter 5, The Front Panel.
When running a test, you can initiate loopbacks and tests on the full bandwidth, or on
the data port fraction. You can also set programmable test patterns.
NOTE: You do not need to inform the telephone company that you are running the
tests. However, if the tests reveal a problem with telephone company service or with
the DSU/CSU, you should inform the telephone company that the DTE equipment or
the DSU/CSU must be removed from service.
- Encore Multi-port 1
- DSU/CSU User Guide 1
- Disclaimer 3
- ISO RegistrationCompliance 4
- Table of Contents 5
- Chapter 2, Installation 2-1 6
- Chapter 3, ConÞguration 3-1 7
- Table of Contents ix 9
- Table of Contents xi 11
- Glossary Glossary-1 13
- Index Index-1 13
- List of Figures G 15
- List of Figures xvii 17
- List of Tables G 19
- List of Tables xxi 21
- Preface G 23
- Typographic Conventions 25
- To follow a link: 26
- To retrace your viewing path: 26
- Examples 26
- Returning a DSU/CSU 28
- Send Us Your Comments 28
- Introduction 29
- DL100 30
- Service 31
- Data ports 32
- Access/Management Features 32
- Compliancy 33
- About the Telnet Utility 33
- Installation 35
- Required Location 36
- Check the Equipment 36
- Equipment Model Numbers 37
- Installation 2-5 39
- Connecting to Power 40
- Installation 2-7 41
- Connecting to the T1 Network 46
- About the Cabling 46
- Determine Correct Distance 47
- ConÞguration 49
- Check the Comm Port Settings 50
- Connecting an ANSI Terminal 51
- ConÞguration 3-5 53
- Access Rights 54
- The Unit ID 55
- Log On from a Terminal 56
- Log On Through Telnet 56
- Log On in Other Conditions 57
- Logging Off 57
- Editing a Parameter 59
- ConÞguration 3-13 61
- (INTERNAL) is used 66
- DSU/CSU and the 66
- ConÞguring the Data Ports 67
- DSU/CSU inverts the 68
- DSU/CSU removes the 1s 68
- Allocating Timeslots 69
- Three Allocation Methods 69
- ConÞguration 3-23 71
- ConÞguring for SNMP 76
- ConÞguration 3-29 77
- How Alarms Are Reported 81
- Menu-7 Alarm I 83
- DSU/CSU is 84
- Menu-8 Alarm II 85
- DSU/CSU waits 89
- Modem Initialization 90
- ConÞguration 3-43 91
- Monitoring and 93
- Management 93
- Monitoring Status 94
- Menu-1 Main Status Parameters 95
- network signal is missing 96
- AUX DTE Status 97
- DATA DTE Status 97
- Menu-2 Data DTE Status 99
- Data DTE Status Parameters 100
- Monitoring Performance 101
- (Figure 4-4) 103
- Displaying the Event Log 107
- Event Log Parameters 108
- The Front Panel 111
- The Interface 112
- Using the Front Panel 113
- (▲) or Down (▼) arrow 113
- (▲) and Down (▼) arrows at 113
- Changing Information 114
- Monitor Submenus 115
- Test Submenus 116
- Running a TEST PATTERN 117
- ConÞguration Submenus 118
- The Front Panel 5-9 119
- The AUX CONFIG Menu 120
- Required Information 120
- Keep a Record 121
- Diagnostics and 123
- Troubleshooting 123
- Adding a Caution Flag 124
- Menu-9 Diagnostics Parameters 126
- 1:1 Pattern QRW Pattern 128
- The Self Test 129
- The Loop DTE Test 129
- The Loop NET Test 130
- The Loop Payload Test 131
- The DTE/NET Test 132
- The Loop Up Remote Test 133
- The Pattern Tests 135
- The Send All Zeroes Test 136
- The Send 1:2 Test 136
- Required Tools 137
- The DSU/CSU does not Power Up 138
- The NET LED is Constantly Red 141
- LEDs do not Illuminate 144
- Running Loopbacks 146
- Running the Pattern Test 147
- Technical SpeciÞcations 149
- DS1 Interface 150
- System Timing 150
- Front Panel 151
- Power Options 151
- Alarm Contacts 152
- Environmental 152
- Regulatory 153
- Diagnostics and Tests 154
- Front Panel LEDs 155
- LEDs (Continued) 157
- T1 line. Non-intrusive 158
- T1 network. Non-intrusive 158
- Technical SpeciÞcations A-11 159
- Factory Default ConÞguration 161
- Not Assigned 162
- Connector Pin 165
- Assignments 165
- DTE Port Pin Assignments 166
- 3 Send toward DTE Tip (T1) 166
- DTE Ring (R1) 166
- 4 Frame Ground 166
- (I/O to all DSUs only) 168
- Adapter Pin Assignments 169
- DTE Clock Rates 170
- ConÞguration Worksheet 171
- SNMP ConÞguration 173
- Glossary 175
- Glossary G-3 177
- Glossary G-5 179
- Glossary G-7 181
- See also 183
- Glossary G-11 185
- Glossary G-13 187
- Glossary G-15 189
- Glossary G-17 191
Related products and manuals for Network switches Encore 24 PORTS NWAY SWITCHING HUB
(28 pages)
(15 pages)© 2020, manymanuals.com. All rights reserved. | 2.489 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals