Encore E 9 Installation Manual

E9 IN REV. A 1 E9 PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Voltage & Temperature Sensor And

E9 IN REV. A 10The Yellow wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hood pin switch

E9 IN REV. A 11This wire provides a 200mA (-) ground output that becomes active 4 seconds before the remote start unit initialize, and remains groun

E9 IN REV. A 12This output is programmable. If programmed rearm a factory installed security system. This wire will supply a pulse whenever the remo

E9 IN REV. A 13 3 PIN DOOR LOCK CONNECTOR: (Maximum 500mA Output) Blue WireGreen Wire( - ) Lock Pulse( + ) Unlock Pulse( - ) Unlock Pulse(+) Loc

E9 IN REV. A 142 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To Al

E9 IN REV. A 154 All Confirmation chirps on Siren Confirmation chirp on only Horn Confirmation chirp on only All Confirmation chirps off 5 +

E9 IN REV. A 16 Five Chirps = 0.8 second Lock, double 0.8 second. Unlock Six Chirps = Double 0.8 second Lock, 0.8 second Unlock Seven Chirps = Door

E9 IN REV. A 172 Push the Valet switch 5times (holding in on the 5th push) until one long chirp is heard then release the valet switch. You are no

E9 IN REV. A 182. Press and hold the valet switch, the timer will immediately start. 3. When the desired interval has passed, release the valet sw

E9 IN REV. A 191. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 6 times (holding in on the 6t

E9 IN REV. A 2Precautions: Please read carefully This Remote Starter with Alarm and Keyless Entry System has been designed to be installed BY PROF

E9 IN REV. A 203. Press and release the transmitter button corresponding to the feature you want to program. Press Transmitter Button One Chirp /

E9 IN REV. A 211. Press button once on the transmitter to start the vehicle. 2. If everything goes well: a. Press button once on the transmitt

E9 IN REV. A 223. Press the transmitter and buttons at the same time to set the “Timer Checking Type”. [3] LED flashes, [3] chirps to confirm t

E9 IN REV. A 234. Press the first, within 3 seconds press and hold the and buttons at the same time on the transmitter for 6 seconds, there

E9 IN REV. A 241. Test the BRAKE shutdown circuit: With the vehicle in park (P), start the vehicle using the remote transmitter. Once the engine is

E9 IN REV. A 25explained to the operator as it is in contrast to the normal operation of a vehicle utilizing an electrical neutral start switch and

E9 IN REV. A 26ENCORE LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and Canada Only) 1. Encore Automotive Systems LLC. WARRANTS th

E9 IN REV. A 27**IMPORTANT NOTE: Any damages resulting from an installation performed by anyone other than a professional installation technician

E9 IN REV. A 3 6 PIN HEAVY GAUGE WIRE HARNESS

E9 IN REV. A 420A20ARed: Remote Start Power 1Red: Remote Start Power 2Violet: Starter (+) OutputPink: Ignition 2 (+) OutputYellow: Ignition 1 (+) Ou

E9 IN REV. A 5Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wires that pass through holes on the

E9 IN REV. A 6Some vehicles have [2] ignition wires that must be power. Connect the PINK wire to the ignition 2 wire from the ignition switch. The i

E9 IN REV. A 7RED WIRE — SYSTEM POWER (+12V CONSTANT) — The RED wire supplies power to the system. Connect this wire to a stable constant +12 volt s

E9 IN REV. A 8 87 87a85 3086 IN4003 Diode H2/1 Blue / Black wire from control module “Start”“On”XCut“Acc”“Off”H1/4 Yellow wire (Ignition 1 output)f

E9 IN REV. A 9 When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is dis